http://www.realoakfloors.co.uk/bona_kemi_adhesives.php Bona Kemi Adhesives Real Oak Floors 2006 http://realoakfloors.co.uk/media/thumbs/713_Lacquered_Rustic_Oak_Narrow_Plank.jpg http://www.realoakfloors.co.uk/bona_kemi_adhesives.php http://realoakfloors.co.uk/bona_d500_adhesive.php Bona D500 Adhesive D500 is a one-component primer for the preparation of substrates prior to the use of parquet adhesives, in particular dispersion adhesives. Solvent free and vapour permeable, it is suitable for both absorbent and non-absorbent substrates (with the exception of magnesium industrial floors). It may also be used for chipboard, panels and similar substrates. Information Less absorption of adhesive into substrate which extends workability Improves quality of subfloor by sealing dust Vapour permeable Application: Dilute D500 1:1 with clean water and mix well. Apply evenly using brush or roller. Avoid puddles of product. Under normal conditions the adhesive may be applied the next day. Adverse site conditions may affect drying time. Drying time: 24 hours depending on the absorbency of the substrate and the room temperature. Coverage: 75g/M squared-concentrated 150g/M squared-diluted Key points The use of primers can not make a poor substrate good, it can make a good substrate better Where very moisture sensitive substrates, such as anhydrite screeds, chipboard etc present or highly absorbent timber is used, a minimum drying time of 24 hours should be allowed infor@realoakfloors.co.uk, (Real Oak Floors) http://realoakfloors.co.uk/bona_d500_adhesive.php Mon, 12 Jan 2009 23:07:45 +0100 http://realoakfloors.co.uk/bona_d700_adhesive.php Bona D700 Adhesive D700 is a solvent-free white glue which meets the requirements of class D3 according to EU 204 and is suitable for gluing various timber materials, especially tongue and groove joints of engineered flooring, pre-finished parquet, laminate floor coverings or similar materials. Its sets quickly and has a good resistance to water. D700 is resistant to moisture and extremes in humidity. Coverage: Aproximately 80-100 linear metres. Application: Cut nozzle at a suitable angle for application to the side of the groove of the timber product. Excess adhesive should be immediately removed from the surfaces of the boards using a dampended cloth. Drying time: The floor may be returned to full use one day after installation. infor@realoakfloors.co.uk, (Real Oak Floors) http://realoakfloors.co.uk/bona_d700_adhesive.php Tue, 03 Feb 2009 23:01:28 +0100 http://realoakfloors.co.uk/bona_r850_flooring_adhesive.php Bona R850 Flooring speed Adhesive Bona 850 speed is an elastic single component silicone based adhesive for bonding of timber to a suitable subfloor. Due to the high flexibility of the dried adhesive stress to the subfloor is greatly reduced. Bona R850 has excellent adhesion to most subfloors, even non absorbent ones. Perfect for use on Bona R410 moisture barrier. Available in 14kg Information Safe and clean Water and solvent free, no swelling of timber Remains elastic once dry Good adhesion to a variety of substrates and timber materials Easy to use Application: Use notched trowel to produce a rib surface Drying time: 24 hours under normal conditions Coverage: 850g/M squared- Mosaic parkett 1000g/M squared-2 layered prefinished parquet 1250g/M squared-22mm boards 3 layered prefinished parquet 1500 g/M squared-Very wide/long boards Key points Replace foil cover to preserve any remaining product Can be used directly onto R410 damp proof membrane Suitable for non-absorbent substrates, ceramic tiles etc. Does not stain prefinished boards Mastic asphalt floors and other sensitive to plasticizers must be treated with R410 first infor@realoakfloors.co.uk, (Real Oak Floors) http://realoakfloors.co.uk/bona_r850_flooring_adhesive.php Tue, 03 Feb 2009 23:01:11 +0100 http://realoakfloors.co.uk/bona_r410_floor_adhesive.php Bona R410 damp proofing Flooring Adhesive Bona R410 is a solvent and water free component epoxy resin for damp-proofing cementitious subfloors prior to installing timber flooring. As a moisture barrier it will function when R.H. is as high as 92-100% Information To be used in order to prevent the impact of moisture on timber due to damp cementitious surfaces or where there is an absence of a DPM. Application: Paint brush, roller or trowel. Two coats need to be applied, the second in alternate direction after 2-3 hours Coverage: Approximately 20sqm Drying time: approximately 24 hours Key Points A damp proofer for cementitious surface where moisture readings are high (CM 5% or RH 90-100%) A two coat system Bona adhesives R850 and R770 can be used directly onto R410 after 2 hours It is important that R410 is applied at the stated coverage The subfloor must be even, clean and physically sound The coverage for the 5KG tin is 20sqm with one coat. Where 2 coats are required (for Damp proofing purposes) the tin will cover 10sqm. Delivery Note Please note that due to the corrosive properties of the Bona R410 Adhesive, this item must be shipped directly from our supplier. Purchasing the adhesive in quantities of more than 1 will not affected delivery costs. infor@realoakfloors.co.uk, (Real Oak Floors) http://realoakfloors.co.uk/bona_r410_floor_adhesive.php Thu, 07 Jan 2010 23:05:41 +0100 http://realoakfloors.co.uk/bona_r770_wood_floor_adhesive.php Bona R770 Wood Floor Adhesive Bona R770 is a two-component polyurethane adhesive which follows DIN 281. It does not contain water or organic solvents and hardens by chemical reaction without shrinking. R770 is especially suitable for timbers extremely sensitive to swelling and for low or non-absorbent substrates, but may also be used for the full area bonding of laminated floor coverings. It has a good open time and an excellent adhesion to almost all substrates and timber materials. Information Especially suitable for moisture sensitive timber types Excellent adhesion to most substrates Long open time (45 minutes) Can be used for the full area bonding of laminated floor coverings Suitable for underfloor heating Application: The hardner should be added to the resin and mixed thoroughly, with a mixing blade on a drill, until a uniform colour is produced. When mixed the pot life is 45 mins so the laying of the timber should be well planned. The adhesive should be applied by notched trowel and a rib structure produced. The parkett should then be laid and firmly pressed down during the 45 minutes open time. Drying time: Under normal conditions the floor may be sanded and sealed 24 hours after installation Coverage: Depends upon type of flooring. Refer to the instructions from the parkett manufacturer, but as a guide: 850g/M squared-Mosaic parkett and similar 1 layered prefinished parkett 1000g/M squared-10mm solid parkett, 2/3 layered prefinished, woodblock (up to 40mm thick, 22mm strip) 1250g/M squared-Endgrain timbers, very wide/long boards Key points Component B (hardener) is harmful. Do not inhale fumes, wear gloves etc Claening agents: acetone/ethanol. Once hardened it can only be removed mechanically (sanding). Can be used directly onto Bona R410 D.P.M infor@realoakfloors.co.uk, (Real Oak Floors) http://realoakfloors.co.uk/bona_r770_wood_floor_adhesive.php Mon, 12 Jan 2009 23:07:44 +0100 http://realoakfloors.co.uk/bona_kemi_h790_wood_flooring_adhesive.php Bona Kemi H790 Wood Flooring Adhesive H790 is a two-component dispersion parquet adhesive which conforms to DIN 281. Immediately after mixing component A (Dispersion) and component B (Powder) a chemical reaction starts. This chemically binds more that 50% of the total water content within the product in approximately four hours. The ratio of free water in the adhesive is less than 11%. It is especially suitable for timbers sensitive to swelling and for low absorbent substrates. Information No solvents therefore no health andamp; safety implications Very low water content (11%) Minimal swelling of the timber High level of adhesion soon after application Application: The two components must be thoroughly mixed using a drill fitted with a mixing blade. Mix until a uniform colour is achieved. Application should be made using a notched trowel of an appropriate size. Application should be made to an area no larger than that which can be laid within 10 minutes. The flooring should be laid onth eadhesive and pressed gently into the surface. Coverage: Depends upon size and type of flooring. It is important that correct rates are used to avoid problems associated with poor adhesion. See below: 850g/M squared-Mosaic parkett (not prefinished) 1000g/M squared-10mm solid parkett,22mm strip flooring, 2 layer prefinished parkett 1250g/M squared-End grain blocks/fingers, 3 layer prefinished parkett, very long/wide boards. Drying times (once mixed): Pot life=45 minutes Open time once spread = 10 minutes After 24 hours the floor may be sanded and sealed Key points H790 is not suitable for bitumen backed blocks, finger mosaic etc. Drying time/cure time may be affected by adverse site conditions such as low temperature and high humidity It is recommended that the substrate be primed using Bona D500 H790 conforms to DIN 821 Suitable for use with under floor heating infor@realoakfloors.co.uk, (Real Oak Floors) http://realoakfloors.co.uk/bona_kemi_h790_wood_flooring_adhesive.php Mon, 12 Jan 2009 23:07:45 +0100 http://realoakfloors.co.uk/bona_s760.php Bona S760 Adhesive S760 is a one-component solvent based parquet adhesive dissolved inorganic solvents, primarily acetone and ethanol, which conforms to DIN281 with low solvent content. The hardened adhesive is hard plastic. It is easy to apply with a rapid setting and due to its relatively long open time it is particularly suitable for laying complicated, technically difficult floors. Suitable substrates include concrete, plywood, cementitious screeds, anhydrite screeds, mastic asphalt and levelling compounds. Information Rapid setting Retains trowel structure Good open time (slightly longer than S750) Easy to apply Application: The S760 should be applied using a trowel appropriate to the flooring being laid. Application should be made to an area no bigger than that can be laid in 15 mins. Note: If the product has been stored for an extended period-stir well prior to use. Coverage: Depends upon size and type of flooring. It is important that correct rates are used to avoid problems associated with poor adhesion. See below: 850/M squared-Mosaic parkett (not prefinished) 1000g/M squared-10mm soild parkett, 22mm strip flooring, 2 layer prefinished parkett 1250g/M squared-End grain blocks/fingers, 3 layer prefinished parkett Drying Time: Open Time=15 minutes After 24 hours the floor may be sanded and sealed under normal conditions Key points S760 is no t suitable for bitumen backed blocks, finger mosaic etc. Drying time/cure time may be affected by adverse site conditions such as low temperature and high humidity It is recommended that the substrate be primed using Bona D500 S760 conforms to DIN 821 Suitable for use with underfloor heating Please Note:As Bona S760 is classed as a hazardous product we are no longer able to deliver this product by post as a result Bona S760 is available for local pick up only. We also highly recommend the use of Everbuild 650 as an alternative to this product. infor@realoakfloors.co.uk, (Real Oak Floors) http://realoakfloors.co.uk/bona_s760.php Mon, 19 Jan 2009 23:00:32 +0100 http://realoakfloors.co.uk/bona_s750_adhesive.php Bona S750 Adhesive S750 is a one-component solvent based parquet adhesive dissolved in organic solvents, primarily acetone and ethanol, which conforms to DIN 281 with low solvent content. The hardened adhesive is hard plastic. IT is easy to apply with a rapid setting and a good open time. For bonding timber flooring to a suitably prepared substrate. Suitable substrates include concrete, plywood, cementitious screeds, anhydrite screeds, mastic asphalt and levelling compounds. Information Rapid setting Retains trowel structure Good open time Easy to apply (slightly higher viscosity than S760) Application: To be applied using a trowel appropriate to the flooring being laid. Application should be made to an area no bigger than that can be laid in 15mins.NOTE If the product has been stored for an extended period-stir well prior to use. Coverage: Depends upon size and type of flooring. It is important that correct rates are used to avoid problems associated with poor adhesion. See below: 850g/M squared-Mosaic parkett (not prefinished) 1000g/M squared-10mm solid parkett, 22mm strip flooring, 2 layer prefinished parkett 1250g/M squared-End grain blocks/fingers, 3 layer prefinished parkett Drying time: open time-15 minutes. After 24 hours the floor may be sanded and sealed under normal conditions Key points S750 is not suitable for bitumen backed blocks, finger mosaic etc. Drying time/cure time may be affected by adverse site conditions such as low temperature and high humidity It is recommended that the substrate be primed using Bona D500 S750 conforms to DIN 821 Suitable for use with underfloor heating infor@realoakfloors.co.uk, (Real Oak Floors) http://realoakfloors.co.uk/bona_s750_adhesive.php Mon, 12 Jan 2009 23:07:43 +0100 http://realoakfloors.co.uk/bona-r860-flooring-adhesive.php Features Bona R860 wood flooring adhesive is an easy to apply, rapid bonding adhesive designed for engineered wood floors and also parquet. This flooring adhesive does not contain plastisizers making it extremely 'green' and safe. How to Apply Bona R860 is a high performing and very fast acting adhesive making it easy to apply and help stablise your wood floor, making it ideal for parquet flooring. Apply to small areas and place your wood flooring on top. Speed up the process by spraying a little water on the substrate or spread adhesive. There is generally no need to use a primer but Bona R410 or R580 will provide extra protection and in the case of Bona R580, will provide a moisture barrier between your wood floor and substrate. Key Features Extremely quick setting High initial tack making it easy to apply Plasticizer free Great adhesion to almost any substrate and wood flooring infor@realoakfloors.co.uk, (Real Oak Floors) http://realoakfloors.co.uk/bona-r860-flooring-adhesive.php Tue, 30 Nov 1999 00:00:00 +0100 http://realoakfloors.co.uk/bona-r580-flooring-adhesive.php Features Bona R580 flooring adhesive is designed for damp sub floors where moisture protection is vital. The silane-based solution also avoids solvents making it safe to apply and use anywhere in your home. How to Use Simply use as a one-component adhesive and apply one coat to your subfloor. Optionally use as a two-component system by adding water allowing bonding to occur faster. Bona R580 flooring adhesive works as a moisture barrier by sealing moisture in the substrate. Apply before R850 or R850T. Please note that Bona R860 and R845 absorb more water making these products less suitable for use with Bona R580. Technical Data One-component with optional two-component applicaiton Fast setting Easy application with trowel Safe handling without transport constraints infor@realoakfloors.co.uk, (Real Oak Floors) http://realoakfloors.co.uk/bona-r580-flooring-adhesive.php Tue, 30 Nov 1999 00:00:00 +0100 http://realoakfloors.co.uk/bona-r845-wood-flooring-adhesive.php Features Bona R845 is a wood flooring adhesive designed to be used with engineered wood flooring. This wood floor glue will reduce tensions in the subfloor and the use of a primer is not needed. The flooring adhesive hardens through a chemical reacction between the adhesive and moisture. Technical Data 1-Component making it to handle Water and solvent free so no swelling of the wood Consistent texture making it to apply with trowel Strong and rapid bonding infor@realoakfloors.co.uk, (Real Oak Floors) http://realoakfloors.co.uk/bona-r845-wood-flooring-adhesive.php Tue, 30 Nov 1999 00:00:00 +0100 http://realoakfloors.co.uk/bona-h650.php Features Bona H650 is a self-levelling compound designed for rapid renovation and repair work. Use prior to Bona R850 wood flooring adhesive. It is recommended to use Bona R850 adhesive after at least an hour and the levelling compound has not exceeded 10mm. Key Features Rapid drying time - cover after just 1 hour High Strength and hardness Low shrinkage infor@realoakfloors.co.uk, (Real Oak Floors) http://realoakfloors.co.uk/bona-h650.php Tue, 30 Nov 1999 00:00:00 +0100 http://realoakfloors.co.uk/bona_glue_click_flooring_adhesive.php Bona - Glue Click GlueClick is a solvent-free white glue which meets the requirements of class D3 according to EN 204. It is suitable for gluing various timber materials especially wooden joint Click systems, tongue and groove pre-finished parquet, laminate floor coverings and chipboard. Different to other D3 glues ClueClick residues or spilt material can, up to two days after application, be removed from pre-finished parquet and laminate floors. infor@realoakfloors.co.uk, (Real Oak Floors) http://realoakfloors.co.uk/bona_glue_click_flooring_adhesive.php Tue, 03 Feb 2009 23:01:31 +0100